EMC XLPEFLEX wind energy shielded control cable is applicable for
free hanging or fixed installation in fin cabin.
Type and Name
EMC XLPEFLEX Wind Energy Shielded Control Cable
1000m Altitude: 1000m
Ambient air temperature: Perennial mean temperature: 10℃
Extreme high temperature: 50℃
Extreme low temperature: -42℃
Average relative humidity: normal value for accumulated year: 80%
Earthquake Proof: Horizontal acceleration: 0.2g
Normal acceleration: 0.1g
Safety factor: 1.67
Note: g is acceleration of gravity. g=9.8m/s²
Extreme wind speed:30.0m/s
Range of Laying
Cables mainly lay in the cabin of fan, where machinery oil may leak
Rated Voltage U0/U: 300/500V
Continues operating temperature:
Min. ambient temperature when laying: -5℃
Min. bending radius :
d: outer diameter
Conductor should comply with the requirements for Class 5 specified
The surface of conductor should be bright and clean no grease, no
burr or bulge or faulted wire to damage the insulation.
Every conductor coat with an isolated layer made from appropriated
The nominal value of the insulation thickness shall comply with
IEC60227-7. The average value of insulation thickness should be no
less than nominal value, and the thinnest part should be no less
than 90% -1mm of nominal value.
Insulation adopts XLPE, whose property should comply with
provisions in IEC60502-1. The insulation should be rapped on
conductor tightly and easy to peel without damaging the insulation,
conductor and coating. The surface of the insulation should be flat
and color evenly.
Insulated conductors are separated by colors, and in accordance
with DIN VDE 0293. Generally, adopted colors are brown, black,
The shield adopts the structure of tinned copper braid and aluminum
foil lapping. The density of tinned copper braid should be no less
The nominal value of sheath thickness should comply with the
requirements of GB9330, and the average value of outer sheath
should be no less than nominal value. The thinnest part should be
no less than 85%-0.1mm of nominal value.
Sheath is made from PVC mixed material, whose properties should
comply with requirements for PVC/ST5 specified in sheet Two of
IEC60227-1. The sheath should tightly rapped on stranded insulated
core or coating. Meanwhile, the outer sheath should be clean and
The outer diameter should comply with requirements in GB9330. The
color for sheath is grey or black.
The ohmic value of conductor should be no more than specifications
in IEC60228 at 20℃.
Finished cables and insulated cores should withstand the rated AC
voltage test of 2500V, and no breakdown in five minutes.
The resistance of insulated conductor should be no more than
Mechanical and physical properties for finished cable insulation
should comply with IEC60502-1.
Mechanical and physical properties for finished cable sheath should
comply with IEC60227-1.
Finished cables should withstand the burning test specified in
EN50265-2-1 or IEC60332-1.
The shield impedance for finished cable should be no more than
10Ω/km at 20 ℃.
Products can leave factory only after passing examination of
technology department. Each package should be shipped with the
product quality inspection certificate.
Products should inspect according to GB9330. If it fails for the
first time in sample inspection, then take another two samples to
examine the failed project. If the two samples are acceptable, then
the products are acceptable, false otherwise. The number of samples
is accepted by both sides, or decided by manufacture at the time of
no requirements from the buyer.
There should be marks of maker, type, nominal cross-section area,
voltage on the cable. The marks should comply with the requirements
for conductor and color specified in DIN VDE 0293-308.
Marks shall be legible, not easy to erase. The writing should be
clearly visible after 10 times graze in absorbent cotton cloth.
Cables can be packed both in coils and in circles. Cables in circle
should be packed on cable specified in JB/T8137. Cables should be
positive sealing, for those outside the circle, protective cover
should be made. And the length of outside should be no more than
Tags should identify:
① Maker or trade-mark
② Type and specifications mm²,V
③ Lengths m
④ Manufacturing Date: Year Month
⑤ Product Standard Code
⑥ Correct direction for circles
Transport and Storage
The cables should avoid high temperature and cable circle does not
Forbid throwing circles with cable from high attitude and
Forbid lifting several circles at the same time. Circles should be
put firm with appropriate methods to avoid tip over.